Faber Air Hub Portable bianco

Air Hub: transform your home into a pure and uncontaminated environment

Faber Air Hub Portable bianco

Air Hub: transform your home into a pure and uncontaminated environment

Air Hub: take care of the air you breathe

The quality of the air in domestic environments is an important issue. Faber puts its technology and experience at the service of well-being, with ecological systems which can eliminate up to 99.99% of viruses and bacteria.

The Air Hub range is designed to ensure our daily well-being in the home environment. It includes the Vertical, Ceiling, T-Shape, and Portable models.

The Vertical, Ceiling, and T-Shape models of Air Hub hoods perform a dual function: they remove steam and cooking odours and improve the quality of domestic air, making it pure and uncontaminated whenever you want. The disinfection cycle can also be activated manually or set thanks to two automatic programs: Night Cycle and Intensive Disinfection.

Air Hub Portable uses the exclusive 4×4 TECH, a combination of technologies with: 4 UV-C lamps and 4 filtration stages that sanitise the air using activated carbon and act on pollutants such as particulates (PM10 and PM2.5) and VOCs.

Faber Air Hub Portable

Faber Air Hub Portable

    FAQs

    The volume of the kitchen determines the required extraction capacity. An effective hood changes the air in the kitchen 10 times per hour*. A powerful motor ensures greater silence and less energy consumption because it is effective at low speeds.
    A hood does not disturb if it extracts sufficiently without exceeding 55 dB(A) of sound power. A powerful motor can also be effective at lower, quieter speeds.
    *Fan Handbook - F. Bleier 1999

    The hood should be installed at a minimum distance of 65cm from the hob. We recommend not installing it more than 75cm from the hob so that it can extract fumes correctly. Furthermore, the fume exhaust should be as close as possible to the hood. Choose ducts of 150mm in diameter (or no less than 120mm), no longer than 3-4 meters with a maximum of 2 bends. Warning: the warranty does not cover any damages caused by not respecting the minimum safety distances.

    A duct diameter of 150mm is optimal for hoods with a flow rate of 300m3/h or higher. If ducting with this diameter cannot be installed, we recommend a diameter of 120mm. Smaller ducting can negatively affect the flow rate and noise level of the hood.

    Before performing the extraction test, ensure that the hood has been installed correctly, following the instructions in the installation booklet provided with the product. A preliminary extraction test can be performed by turning on both the hood and the hob, and then bringing a pan of water to a boil. If the installation is correct and the poor extraction is due to a product defect, request help from the authorised Faber Technical Assistance Centre (info at the link https://www.faberspa.com/centri-assistenza/) by sending the details of the code written on the label inside the hood. Alternatively, you can open a service ticket by calling the number +353 (0) 15339862

    The extraction capacity and noise level of Faber hoods are measured according to the international standards IEC/EN 61591 and IEC/EN 60704-3 (sound power), specifically devised by certification bodies to detect the performances of kitchen hoods. These methods reproduce typical installation and operating conditions, therefore providing realistic and reliable data. Demand that the performance of hoods refer to these standards: you will be able to rely on correct, complete, and reliable information – just as we provide. Our laboratory is accredited by IMQ and NEMKO, and all performances of Faber hoods, including the grease capture capacity of the filters and the brightness of the lamps, are measured internally.

    To clean your kitchen hood use a soft cloth and a chlorine-free neutral detergent to avoid damaging the finish. To discover the range of Faber products for cleaning hoods and kitchen worktops, visit the Filters and Accessories page.

    You can download the instruction booklet by entering the model code of the hood in the Product Documentation section, Support area.

    Before contacting Technical Assistance to request help, consult the “Use” and “Maintenance” sections of the hood’s instruction booklet.

    Check the installation, ensuring that it has been carried out as per the instruction booklet provided with the hood. If the installation is correct, request the help of the authorised Faber Technical Assistance Centre (info at the link https://www.faberspa.com/centri-assistenza/), by sending the code on the label inside the hood. Alternatively, open a service ticket by calling the number +353 (0) 15339862

    The model of each hood is shown on the label inside the product (identifiable by removing the metal filters/grid). This label has a service code, in the top right part, of 7 or 9 digits starting with 63..., or a 10-digit code with the format 110.xxxx.xxx.

    If the label is illegible or worn, assistance can be requested by filling out the Form in the Support section.

    The hood’s noise is caused by the passage of air inside it during operation. Faber hood components are designed to reduce the obstacles to the airflow, achieving excellent results in terms of low noise emission. An effective precaution to prevent an increase in noise is to use properly sized ducting (120-150 mm in diameter) for the air outlet. Dirty or saturated filters can obstruct the airflow: periodic cleaning (or replacement) of the filters ensures a smooth airflow. Moreover, the hood can be soundproofed by adopting Faber’s innovative noise-reduction technologies. Discover our technologies.

    Yes, you can request the warranty certificate by filling out the Form in the Support section.

    Check the installation, ensuring that it has been carried out as per the instruction booklet provided with the hood. If the installation is correct and the noise is generated by the product, request the help of the authorised Faber Technical Assistance Centre (info at the link https://www.faberspa.com/centri-assistenza/), by sending the code on the label inside the hood. Alternatively, open a service ticket by calling the number +353 (0) 15339862

    Contact the local authorised Faber Technical Assistance Centre (info at the link https://www.faberspa.com/centri-assistenza/), sending the code on the label inside the hood. Alternatively, open a service ticket by calling the number +353 (0) 15339862

    Any aesthetic defect of the product must be reported to the technician at the time of installation, or when opening the hood’s packaging. Subsequent complaints and any action from the Technical Assistance Centre will not be covered by the warranty.

    No, the minimum distance required in the instruction booklet must be respected, both for the warranty to be valid and for safety in the kitchen environment.

    Yes, the same hole will then be connected to the ducting from the hood. The hole must have a diameter of at least 120 mm.

    Here you can place an explanation or answer to the question.

    Here you can place an explanation or answer to the question.

    Here you can place an explanation or answer to the question.

    Continue +